Screws for attaching the panels to framework are included.

     If the framework is aluminum tubing, 1 1/4" epoxy coated aluminum self- tapping screws are included.

     If the framework is 1/2" steel tubing, 1" aluminum screws will be included, and a pilot hole must also be drilled.

     The screwheads are painted to match the rubber color.  Screws should be installed every 12".

AFRAME RUBBERIZED PANELS: the aframe has 3 panels/side (photo A). The panels can be slatless, or have slats as shown. Contacts are 42", universal for all venues.

Each panel is 35 3/4" wide and 36" long, so 9' long when installed on the frame.  


         Panels for a SLATLESS aframe (6 panels) $950

         Panels for an aframe WITH SLATS (6 panels) $1295

LIKE THE RUBBERIZED SURFACE, but also want a new base to have the rubber on? And would you like to change just the contact zones when switching between venues? The idea is finally developed and tested! If your aframe, dogwalk or seesaw has an aluminum or metal framework, you can now get modular panels with a rubber surface PERMANENTLY applied!


SEESAW RUBBERIZED PANELS: the 12' seesaw has 3 panels total, with either 36" or 42" contacts. The 8' seesaw has 2 panels with either 36" or 42" contacts.

Each panel is 11 3/4" wide x 48" long, so either 12' or 8' total length when installed.


        Panels for a 12' seesaw (3 panels)  $250

        Panels for an 8' seesaw,OR2 contact zones w/o slats (2 panels)  $185


Panels for use with FCI:

Rubberized panels are now available for use with FCI regulations. There are limitations to length, and the width is fixed at precut sizes. If a shorter length is wanted, please put the info in customer comments at checkout.


FCI Seesaw panels (3 panels total) - max length 365cm, width 298mm, 900mm contact zones $250


FCI Dogwalk panels with 12 slats (9 panels total)- max length per plank 365cm, width 298mm, 900mm contact zones $925


FCI Aframe panels with 9 slats (6 panels total)- max length per side 274cm, width 908mm, 1060mm contact zones $1325


the aluminum product we use as a base is a 2-sided prefinished aluminum composite, consisting of two 30mm aluminum sheets laminated to both sides of a polyethylene core.

DOGWALK RUBBERIZED PANELS: the 12' dogwalk has 3 panels per ramp/center, total of 9 panels with either 36" or 42" contacts, and choice of slats or no slats on the ramps. The 8' dogwalk has 2 panels per ramp/center, total of 6 panels with either 36" or 42" contacts, and choice of slats or no slats on the ramps.

The 36" contact ramps have 9 slats, the 42" has 10 slats.


If using the dogwalk between venues that have different length contacts, there are 2 options to change the contact zones: 1) unscrew and trade out the bottom panels (4' long ea.) that contain the contact zones. 2) purchase a second set of ramp panels (12' long total) when a second set of ramp framework will be used and the ramps are changed out for the different venues.


Each panel is 11 3/4" wide and 48" long, so each ramp/center plank 12' or 8' total length when installed on the frame pieces.


Panels for a complete 12' dogwalk (9 panels) with 36" or 42" contacts, WITH slats    $895

Panels for a complete 12' dogwalk (9 panels) with 36" or 42" contacts, NO SLATS    $695

2 contact zone Panels WITH slats  $210    2 contact zone Panels NO SLATS   $185

2 - 12' ramps WITH slats  (6 panels)  $695     2- 12' ramps NO SLATS (6 panels)  $495

  

Panels for a complete 8' dogwalk (6 panels) with 36" or 42" contacts, WITH slats  $550

Panels for a complete 8' dogwalk (6 panels) with 36" or 42" contacts NO SLATS   $495

PLEASE NOTE:
The aframe panels need to have proper vertical and horizontal supports on the framework. The seams of the aframe panels are at every 36", so either horizontal support at these measurements, or two vertical supports (top to bottom, see photo) will be necessary.

RUBBER ON THE RUN!

For a free sample of rubberized panel, fill out form below:

(offer good for US addresses only)